Flyers & Print

Router Templates for Woodworking: Make Reusable Jigs

Printed paper pattern clipped to MDF showing router templates for a curve

Router templates are simple guides that let a woodworker cut the same shape again and again. A well-made template turns a tricky curve into a routine job, and it can print from a paper pattern, so it sits comfortably alongside the printable designs on this site. If you have ever struggled to match two matching chair legs or to cut a row of identical panels, this approach will make the work far more consistent.

What Router Templates Do

A template is a rigid pattern with the exact edge you want. You fix it to your workpiece, then run a router with a guide against the template’s edge. The cutter follows the shape, copying it into the wood. Because the pattern does the steering, your results depend more on the template than on your steady hand.

There are two main ways to follow a template. A guide bushing, mounted on the router base, rides against the template while the bit extends through it. A bearing-guided bit has a small wheel that rolls along the pattern. Flush-trim bits and pattern bits use the second method, cutting the workpiece to match a template that sits above or below it.

Choosing Material for Router Templates

Medium density fibreboard, usually called MDF, is the favourite. It is cheap, flat, easy to shape and has smooth edges that guides slide along. Hardboard works for thin templates, and acrylic gives a durable, see-through option when you need to align grain or marks. Plywood is fine, but its layers can create small flaws along the edge.

Thickness depends on the method. A thickness of 6 to 12 millimetres (roughly a quarter to a half inch) suits most bearing-guided work. Make sure it is stiff enough not to flex.

Designing and Marking the Shape

Draw the shape at full size on paper or print it from a design file. Check dimensions twice, since an error in the template repeats on every part. For symmetrical shapes, draw half and fold, or use a ruler and compass for consistent curves.

Transfer the pattern to the template material with spray adhesive or by tracing through carbon paper. Cut slightly outside the line with a jigsaw or bandsaw, then bring the edge to the line with a file, sandpaper or a spindle sander. Fair curves by running your fingertips along the edge; any bump you feel will show in the finished part.

Offsets Matter

If you use a guide bushing, the cut is smaller or larger than the template by the difference between the bushing’s outside diameter and the bit’s diameter. Calculate this offset and adjust the template size accordingly. Make a test piece from scrap before you cut the good wood.

Setting Up and Cutting Safely

Secure the template to the workpiece with double-sided tape, clamps or small screws in waste areas. Rough-cut the shape with a jigsaw first, leaving about 3 millimetres of excess, so the router only trims a little material.

Wear eye and hearing protection and a dust mask. Take shallow passes if the bit is cutting deep. Route against the rotation of the bit, moving the router counter-clockwise around the outside of a shape and clockwise on the inside, so it pulls into the template rather than away. Keep both hands firmly on the router, and let it reach full speed before touching the wood.

Common Problems and Fixes

Burn marks usually mean a dull bit or slow movement. Tear-out near end grain can be reduced by climbing slightly or by backing the area with scrap. If the finished piece differs from the template, check for dust under the bearing, a loose collet or a bit that has slipped.

Storing and Reusing

Label every template with the project name and dimensions. Drill a hole to hang it on a wall hook. Store flat or on edge to prevent warping. Over time you will build a library of shapes you can use for furniture, signs and craft projects.

If you want to document your jigs or sell patterns, a clean, printable layout helps. Our post on choosing a website template shows how to present shop designs online, and the checklist in pricing your services can help if you start taking commissions.

A Worked Example: Template for a Simple Curved Panel

Suppose you want six matching cabinet doors with a shallow arch at the top. Draw the arch on paper using a flexible batten held by two nails, trace it onto MDF, cut close with a jigsaw and smooth the line with a sanding block. Clamp the template over the first door blank, rough-cut it, then trim flush with a pattern bit. The second door takes five minutes, because the template carries all the information. By the sixth, the arches are identical and the only effort left is sanding.

Final Advice

Spend extra time on the template, because every cut depends on it. A careful hour at the bench saves many hours of fixing later, and a good pattern will outlast the project that made it necessary.

Written by thadmin_r7

The Templates Hub editorial team writes practical, plain-English guides for everyday readers.

More articles by this author →

Related posts

↑